View SGM6230_8338232.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SGM6230 2a, 38v, 385khz step-down converter general description the SGM6230 is a current-mode step-down regulator with an internal power mosfet. this device achieves 2a continuous output current over a wide input supply range from 4.5v to 38v with excellent load and line regulations. the switching frequency of SGM6230 is 385khz and current mode operation provides fast transient response and eases loop stabilization. the SGM6230 is highly efficient with peak efficiency at 94% when in operation. in shutdown mode the regulator draws less than 18a of supply current. protection features include cycle-by-cycle current limit and thermal shutdown. the device also includes an internal soft-start and an external adjustable soft-start function to limit the inrush current and prevent the overshoot of output voltage. the SGM6230 is available in green soic-8 (exposed pad) package and requires a minimum number of readily available external components to complete a 2a step- down dc/dc converter solution. features 2a output current high efficiency: up to 94% 4.5v to 38v input voltage range < 18a shutdown supply current 100m ? internal power mosfet switch fixed 385khz switching frequency output adjustable from 0.8v to 32v cycle-by-cycle current limit protection thermal shutdown protection under-voltage lockout stable with low esr ceramic capacitors -40 to +85 operating temperature range available in green soic-8 (exposed pad) package applications distributed power systems battery chargers flat panel tvs set-top boxes pre-regulator for linear regulators cigarette lighter powered devices dvd/pvr devices typical application in bs sw fb comp gnd ss en SGM6230 c5 10nf input 4.5v to 38v enable output 3.3v/2a c4 0.1 f r3 6.49k r2 10.5k r1 33k l 10 h c3 5.6nf c in 22 f c out 47 f c6 optional d1 b340a r4 10 or shorted rev. a. 1 sg micro corp www.sg-micro.com
SGM6230 2a, 38v, 385khz step-down converter 2 sg micro corp www.sg-micro.com package/ordering information model pin- package specified temperature range ordering number package marking package option SGM6230 soic-8 (exposed pad) -40c to +85c SGM6230yps8g/tr sgm 6230yps8 xxxxx tape and reel, 2500 note: xxxxx = date code and vendor code. absolute maximum ratings supply voltage v in .................................................. -0.3v to 40v sw voltage v sw ........................................... -0.5v to v in + 0.3v boost voltage v bs ................................... v sw - 0.3v to v sw + 6v all other pins............................................................ -0.3v to 6v package thermal resistance soic-8 (exposed pad), ja .................. ............... ............50 /w operating temperature range........ ...................- 40c to +85c junction temperature........................................................150c storage temperature range........... ..................-65c to +150c lead temperature (soldering, 10s)...................................260c esd susceptibility hbm.................... ..................... ...................... .................. 4000v mm..................................................................................... 200v note: stresses beyond those listed under ?absolute maximum ratings? may cause permanent damage to the device. these are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the s pecifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. caution this integrated circuit can be damaged by esd if you don?t pay attention to esd protection. sgmicro recommends that all integrated circuits be handled with appropriate precautions. failure to observe proper handling and installation procedures can cause damage. esd damage can range from subtle performance degradation to complete device failure. precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. sgmicro reserves the right to make any change in circuit design, specification or other related things if necessary without notice at any time. please contact sgmicro sales office to get the latest datasheet.
SGM6230 2a, 38v, 385khz step-down converter 3 sg micro corp www.sg-micro.com pin configuration (top view) 3 1 2 soic-8 (exposed pad) gnd bs sw 4 6 8 7 5 in fb ss comp en gnd pin description pin name function 1 bs high-side gate drive boost input. bs supplies the driver for the high-side n-channel mosfet switch. connect a 10nf or greater capacitor from sw to bs to power the high-side switch. a 10 ? resistor placed between sw and bs cap is strongly recommended to reduce sw spike voltage. 2 in power input. in supplies the power to the ic, as well as the step-down converter switches. drive in with a 4.5v to 38v power source. bypass in to gnd with a sufficiently large capacitor to eliminate noise on the input to the ic. 3 sw power switching output. sw is the switching node that supplies power to the output. connect the output lc filter from sw to the output load. note that a capacitor is required from sw to bs to power the high-side switch. 4 gnd ground. (connect the exposed pad on backside to pin 4.) 5 fb feedback input. the voltage at this pin is regulated to 0.8v. connected to the resistor divider between output and ground to set output voltage. 6 comp compensation node. comp is used to compensate the regulation control loop. connect a series rc network from comp to gnd to comp ensate the regulation control loop. in some cases, an additional capacitor from comp to gnd is required. 7 en enable input. en is a digital input that turns the regulator on or off. drive en high to turn on the regulator, and drive en low to turn it off. output voltage is discharged when the ic is off. for automatic startup, leave en unconnected. 8 ss soft-start control input. ss controls the soft-start period. connect a capacitor from ss to gnd to set the soft-start period. a 0.1f capacitor sets the soft-start period to 10ms. to disable the soft-start feature, leave ss unconnected. exposed pad gnd power ground exposed pad. must be connected to gnd plane.
SGM6230 2a, 38v, 385khz step-down converter 4 sg micro corp www.sg-micro.com electrical characteristics (v in = 12v, t a = +25c, unless otherwise noted.) parameter symbol conditions min typ max units input voltage range v in 4.5 38 v feedback voltage v fb 0.776 0.8 0.824 v shutdown supply current i shdn v en = 0v 10 18 a quiescent supply current i q v en = 2.6v, v fb = 1v 0.8 1.7 ma high-side switch (m1) on-resistance r onh 100 m ? low-side switch (m2) on-resistance r onl 10 ? error amplifier transconductance g ea ? v fb = 12.5mv 500 800 1120 a/v error amplifier voltage gain a ea 10000 v/v sw leakage current i lsw v en = 0v, v sw = 0v 1 a current limit i lim 4.2 a current sense to comp transconductance g cs 6.2 a/v maximum duty cycle d max v fb = 0.6v 90 % minimum duty cycle d min v fb = 1v 0 % en threshold voltage v ih 1.2 v en threshold voltage v il 0.4 v en pull-up current v en = 0v 0.8 1.4 2 a oscillator frequency f s 335 385 435 khz short-circuit oscillator frequency v fb = 0v 25 38 60 khz under-voltage lockout threshold v in rising 3.5 3.8 4.2 v under-voltage lockout threshold hysteresis 230 mv soft-start period c ss = 0.1 f 10 ms thermal shutdown temperature t shdn 160
SGM6230 2a, 38v, 385khz step-down converter 5 sg micro corp www.sg-micro.com typical performance characteristics v in = 12v, c in = 22f, c out = 47f and t a = +25c, unless otherwise noted. efficiency vs. load current 30 40 50 60 70 80 90 100 00.511.522.533.5 load current (a) efficiency (%) v in = 5v v in = 24v v out =3.3v l = 10 h v in = 12v efficiency vs. load current 30 40 50 60 70 80 90 100 00.511.522.533.5 load current (a) efficiency (%) v in = 9v v in = 24v v out = 5v l = 10 h v in = 12v switching waveforms 1a/div 10mv/div 100mv/div 10v/div i l v out v in v sw v in = 12v, v out = 3.3v, r load = 2 ? time (2 s/div) soft-start waveforms 1v/div 1a/div time (4ms/div) v out i l v in = 12v, v out = 3.3v, r load = 2 ? turn-off waveforms 1v/div 1a/div time (100 s/div) v out i l v in = 12v, v out = 3.3v, r load = 2 ? v out i l 100mv/div 1a/div time (200 s/div) v in = 12v, v out = 3.3v, 1a to 2a step load transient response
SGM6230 2a, 38v, 385khz step-down converter 6 sg micro corp www.sg-micro.com typical performance characteristics v in = 12v, c in = 22f, c out = 47f and t a = +25c, unless otherwise noted. efficiency vs. load current 30 40 50 60 70 80 90 100 00.511.522.533.5 load current (a) efficiency (%) v out = 3.3v v in = 36v feedback voltage vs. temperature 0.77 0.78 0.79 0.80 0.81 0.82 0.83 -50 -25 0 25 50 75 100 temperature ( ) feedback voltage (v) peak current limit vs. temperature 3.5 3.7 3.9 4.1 4.3 4.5 -50 -25 0 25 50 75 100 temperature ( ) peak current limit (a) efficiency vs. load current 30 40 50 60 70 80 90 100 00.511.522.533.5 load current (a) efficiency (%) v out = 5v v in = 36v oscillator frequency vs. temperature 320 340 360 380 400 420 -50 -25 0 25 50 75 100 temperature ( ) oscillator frequency (khz)
SGM6230 2a, 38v, 385khz step-down converter 7 sg micro corp www.sg-micro.com operation main control loop the SGM6230 is current-mode step-down regulator. it regulates input voltages from 4.5v to 38v down to an output voltage as low as 0.8v, and is able to supply up to 2a of load current. the SGM6230 uses current-mode control to regulate the output voltage. the output voltage is measured at fb through a resistive voltage divider and amplified through the internal error amplifier. the output current of the transconductance error amplifier is presented at comp where a network compensates the regulation control system. the voltage at comp is compared to the switch current measured internally to control the output voltage. the converter uses an internal n-channel mosfet switch to step-down the input voltage to the regulated output voltage. a boost capacitor connected between sw and bs drives the gate of mosfet, and makes it greater than input voltage while sw is high. thus, the mosfet will be in low resistance conducting state. the capacitor is internally charged while sw is low. an internal 10 ? switch from sw to gnd is used to ensure that sw is pulled to gnd during shutdown to fully charge the bs capacitor. soft-start the device includes a soft-start to limit the inrush current and prevent the overshoot of output voltage. the soft-start time can be programmed by the external soft-start capacitor and it is calculated as: t ss = 100k ? c ss for example, c ss =0.1 f corresponds to a 10ms soft- start time. to get perfect power on start performance, right soft-start time must be added to adjust the sequence between power supply and the output voltage in order to guarantee the self-boost capacitor is charged correctly. usually a 1 f c ss is good enough, if the power supply is decoupled by big input capacitor, a long soft-start time is preferred.
SGM6230 2a, 38v, 385khz step-down converter 8 sg micro corp www.sg-micro.com application information setting the output voltage the output voltage is set using a resistive voltage divider from the output voltage to fb pin. the voltage divider divides the output voltage down to the feedback voltage by the ratio: r2 r1 r2 v v out fb ? ? where v fb is the feedback voltage and v out is the output voltage. thus the output voltage is: 2 r 2 r 1 r 8 . 0 v out ? ? ? the value for r2 can be as high as 100k ? , but a typical value is 10k ? . using that value, r1 is determined by: r1 = 12.5 (v out - 0.8) (k ? ) for example, for a 3.3v output voltage, r2 is 10k ? , and r1 is 31.25k ? . inductor the inductor is required to su pply constant current to the output load while being driven by the switched input voltage. a larger value inductor will result in less ripple current that will result in lower output ripple voltage. however, the larger value inductor will have a larger physical size, higher series resistance, and/or lower saturation current. a good rule for determining the inductance to use is to allow the peak-to-peak ripple current in the inductor to be approximately 30% of the maximum switch current limit. also, make sure that the peak inductor current is below the maximum switch current limit. the inductance value can be calculated by: ? ? ? ? ? ? ? ? ? ? ? ? in out l s out v v 1 i f v l where v in is the input voltage, f s is the 385khz switching frequency, and i l is the peak-to-peak inductor ripple current. choose an inductor that w ill not saturate under the maximum inductor peak current. the peak inductor current can be calculated by: ? ? ? ? ? ? ? ? ? ? ? ? ? ? in out s out load lp v v 1 l f 2 v i i i load is the load current. output rectifier diode the output rectifier diode supplies the current to the inductor when the high-side switch is off. to reduce losses due to the diode forward voltage and recovery times, use a schottky diode. choose a diode whose maximum reverse voltage rating is greater than the maximum input voltage, and whose current rating is greater than the maximum load current. table 1 lists example schottky diodes and manufacturers. table 1. diode selection guide diode voltage, current rating manufacturer sk33 30v, 3a diodes inc. sk34 40v, 3a diodes inc. b330 30v, 3a diodes inc. b340 40v, 3a diodes inc. mbrs330 30v, 3a on semiconductor mbrs340 40v, 3a on semiconductor input capacitor the input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the ac current to the step-down converter while maintaining the dc input voltage. use low esr capacitors for the best performance. ceramic capacitors are preferred, but tantalum or low-esr electrolytic capacitors may also suffice. since the input capacitor (c in ) absorbs the input switching current, it requires an adequate ripple current rating.
SGM6230 2a, 38v, 385khz step-down converter 9 sg micro corp www.sg-micro.com application information the rms current in the input capacitor can be estimated by: ? ? ? ? ? ? ? ? ? ? ? ? in out in out load rms v v 1 v v i i the worst-case condition occurs at v in = 2v out , where: 2 i i load rms(max) ? for simplification, choose th e input capacitor whose rms current rating is greater than half of the maximum load current. the input capacitor can be electrolytic, tantalum or ceramic. when using electrolytic or tantalum capacitors, a small, high quality ceramic capacitor, i.e. 0.1f, should be placed as close to the ic as possible. when using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. the input voltage ripple caused by capacitance can be estimated by: ? ? ? ? ? ? ? ? ? ? ? ? ? in out in out in s load in v v 1 v v c f i v c in is the input capacitance value. output capacitor the output capacitor (c out ) is required to maintain the dc output voltage. ceramic, tantalum, or low esr electrolytic capacitors are recommended. low esr capacitors are preferred to keep the output voltage ripple low. the output voltage ripple can be estimated by: ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? out s esr in out s out out c f 8 1 r v v 1 l f v v where l is the inductor value, c out is the output capacitance value, and r esr is the equivalent series resistance (esr) value of the output capacitor. in the case of ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. the output voltage ripple is mainly caused by the capacitance. for simplification, the output voltage ripple can be estimated by: ? ? ? ? ? ? ? ? ? ? ? ? ? ? in out out 2 s out out v v 1 c l f 8 v v in the case of tantalum or electrolytic capacitors, the esr dominates the impedance at the switching frequency. for simplification, the output ripple can be approximated to: esr in out s out out r v v 1 l f v v ? ? ? ? ? ? ? ? ? ? ? ? ? the characteristics of the output capacitor also affect the stability of the regulation system. the SGM6230 can be optimized for a wide range of capacitance and esr values. compensation components SGM6230 employs current mode control for easy compensation and fast transient response. the system stability and transient response are controlled through the comp pin. comp pin is the output of the internal transconductance error amplifier. a serial capacitor and resistor combination sets a pole-zero combination to control the characteristics of the control system. the dc gain of the voltage feedback loop is given by: out fb ea cs load vdc v v a g r a ? ? ? ? where a ea is the error amplifier voltage gain, 10000v/v, g cs is the current sense transconductance, 6.2a/v, and r load is the load resistor value. the system has two poles of importance. one is due to the compensation capacitor (c3) and the output resistor of error amplifier, and the other is due to the output capacitor and the load resistor. these poles are located at: ea ea p1 a c3 2 g f ? ? ? load out p2 r c 2 1 f ? ? ?
SGM6230 2a, 38v, 385khz step-down converter 10 sg micro corp www.sg-micro.com application information g ea is the error amplifier transconductance, 800a/v. the system has one zero of importance, due to the compensation capacitor (c3) and the compensation resistor (r3). this zero is located at: r3 c3 2 1 f z1 ? ? ? the system may have another zero of importance, if the output capacitor has a large capacitance and/or a high esr value. the zero, due to the esr and capacitance of the output capacitor, is located at: esr out esr r c 2 1 f ? ? ? in this case, a third pole set by the compensation capacitor (c6) and the compensation resistor (r3) is used to compensate the effect of the esr zero on the loop gain. this pole is located at: r3 c6 2 1 f p3 ? ? ? the goal of compensation design is to shape the converter transfer function to get a desired loop gain. the system crossover frequency where the feedback loop has the unity gain is important. lower crossover frequencies result in slower line and load transient responses, while higher crossover frequencies could cause system unstable. a good rule of thumb is to set the crossover frequency to approximately one-thirtieth of the switching frequency. switching frequency for the SGM6230 is 385khz, so the desired crossover frequency is around 13khz. table 2 lists the typical values of compensation components for some standard output voltages with various output capacitors and inductors. the values of the compensation components have been optimized for fast transient responses an d good stability at given conditions. table 2. compensation values for typical output voltage/ capacitor combinations v out (v) l (h) c out (f) r3 (k ? ) c3 (nf) r1 (k ? ) r2 (k ? ) 0.8 4.7 47/222 0.499 8.2 0 10.5 1.2 4.7 47/222 0.499 22 4.99 10 1.8 4.7 47/222 0.499 22 10.2 8.2 2.5 4.7-6.8 47/222 1.2 22 22.6 10.7 3.3 6.8-10 47/222 6.49 5.6 33 10.5 5 10-15 47/222 3 22 52.3 10 12 15-22 47/222 5 8.2 140 10 in bs sw fb comp gnd ss en SGM6230 c5 10nf input enable output c4 0.1 f r3 r2 r1 l c3 c in 10 f 2 c out c6 optional d1 b340a r4 10 or shorted figure 2. typical application circuit
SGM6230 2a, 38v, 385khz step-down converter 11 sg micro corp www.sg-micro.com application information to optimize the compensation components for conditions not listed in table2, the following procedure can be used. 1. choose the compensation resistor (r3) to set the desired crossover frequency. determine the r3 value by the following equation: fb out cs ea c out v v g g f c 2 r3 ? ? ? ? ? where f c is the desired crossover frequency (which typically has a value no higher than 13khz). 2. choose the compensation capacitor (c3) to achieve the desired phase margin. for applications with typical inductor values, setting the compensation zero, f z1 , below one-forth of the crossover frequency provides sufficient phase margin. determine the c3 value by the following equation: c f r3 2 4 c3 ? ? ? where, r3 is the compensation resistor value and f c is the desired crossover frequency, 13khz. 3. determine if the second compensation capacitor (c6) is required. it is required if the esr zero of the output capacitor is located at less than half of the 385khz switching frequency, or the fo llowing relationship is valid: 2 f r c 2 1 s esr out ? ? ? where, c out is the output capacitance value, r esr is the esr value of the output capacitor, and f s is the 385khz switching frequency. if this is the case, then add the second compensation capacitor (c6) to set the pole f p3 at the location of the esr zero. determine the c6 value by the equation: r3 r c c6 esr out ? ? where, c out is the output capacitance value, r esr is the esr value of the output capacitor, and r3 is the compensation resistor.
SGM6230 2a, 38v, 385khz step-down converter 12 sg micro corp www.sg-micro.com package outline dimensions soic-8 (exposed pad) d e e1 e b a a2 a1 c l e2 d1 3.302 2.413 0.61 1.27 1.91 5.56 recommended land pattern (unit: mm) dimensions in millimeters dimensions in inches symbol min max min max a 1.700 0.067 a1 0.000 0.100 0.000 0.004 a2 1.350 1.550 0.053 0.061 b 0.330 0.510 0.013 0.020 c 0.170 0.250 0.007 0.010 d 4.700 5.100 0.185 0.201 d1 3.202 3.402 0.126 0.134 e 3.800 4.000 0.150 0.157 e1 5.800 6.200 0.228 0.244 e2 2.313 2.513 0.091 0.099 e 1.27 bsc 0.050 bsc l 0.400 1.270 0.016 0.050 0 8 0 8
SGM6230 2a, 38v, 385khz step-down converter 13 sg micro corp www.sg-micro.com tape and reel information note: the picture is only for reference. please make the object as the standard. key parameter list of tape and reel package type reel diameter reel width w1 (mm) a0 (mm) b0 (mm) k0 (mm) p0 (mm) p1 (mm) p2 (mm) w (mm) pin1 quadrant soic-8 (exposed pad) 13 12.4 6.4 5.4 2.1 4.0 8.0 2.0 12.0 q1 reel width (w1) reel diameter reel dimensions tape dimensions direction of feed p2 p0 w p1 a0 k0 b0 q1 q2 q4 q3 q3 q4 q2 q1 q3 q4 q2 q1
SGM6230 2a, 38v, 385khz step-down converter 14 sg micro corp www.sg-micro.com carton box dimensions note: the picture is only for reference. please make the object as the standard. key parameter list of carton box reel type length (mm) width (mm) height (mm) pizza/carton 13 386 280 370 5

▲Up To Search▲

Price & Availability of SGM6230

	To Download SGM6230 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .